Fuji K-Series KL-L, M, H Single-Foot Spinning Guides - Torzite
Specifications
Fuji K-Series KL-L, M, H Single-Foot Spinning Guides - Torzite
Product Details
The Fuji KL series features single-foot spinning guides in three frame heights—Low (L), Medium (M), and High (H)—to offer precise control over guide train layouts for spinning rods. Whether you're building a traditional New Guide Concept (NGC) rod or a cutting-edge KR Concept layout, KL guides deliver lightweight strength, optimal line control, and Fuji’s signature tangle-free performance.
- KL-L: Low profile for compact guide trains
- KL-M: Medium height for progressive reduction layouts
- KL-H: High frame design for KR Concept and braid-specific setups
Key Features:
- Three Height Profiles (L, M, H): Customize reduction trains for ideal casting performance
- Tangle-Free K-Series Design: Sloped frame resists line wrap, especially with braid
- Slim & Lightweight: Ideal for sensitivity-focused builds
- Part of the KR Concept System: Often used with KB (belly) and KT (runner) guides
- Multiple Ring Options: Available in Torzite®, SiC, Alconite®, Fazlite®, and Concept “O”
Recommended For:
Spinning rods in freshwater and saltwater applications. Perfect for custom guide layouts where precise height control is required for line management and casting efficiency.
KR Guide Placement Software
Size Chart
| Ring Size | Frame Height | Height (mm) | Foot Length (mm) | Total Length (mm) |
|---|---|---|---|---|
| 5 | L | 9.3 | 7.4 | 12.1 |
| 5.5 | L | 10.8 | 9.2 | 14.1 |
| 5.5 | M | 14.6 | 10.0 | 16.8 |
| 6 | L | 12.2 | 9.2 | 15.5 |
| 6 | M | 18.4 | 11.0 | 18.0 |
| 7 | L | 13.2 | 9.4 | 16.0 |
| 7 | M | 19.4 | 11.0 | 19.3 |
| 8 | M | 20.8 | 12.0 | 21.3 |
| 8 | H | 26.8 | 13.5 | 24.0 |
| 10 | H | 30.2 | 16.0 | 28.6 |
| 12 | H | 31.8 | 17.0 | 29.0 |
| 16 | H | 43.3 | 18.0 | 35.4 |
| 20 | H | 50.8 | 20.0 | 37.5 |
| 25 | H | 55.9 | 22.0 | 43.4 |
Frame Height Key: L = Low, M = Medium, H = High
Warning: California's Proposition 65
Proposition 65 Warning
CA WARNING.
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to https://www.P65Warnings.ca.gov
Files & Documents
Good guides. Light and saltwater proof. A little pricey but with torzites slimmer ring you can use half size to one size smaller ring and still run your leader knots though these guides. This reduces guide weight creating a better preforming more sensitive rod.
KLH Alconite vs torzite. Is it worth the extra cost?
I wanted to see if the extra cost the torzite guides vs the alconite is justified by extra performance that a torzite guide might provide. I build two rods that were exactly the same except one had Alonite KLH guides and the other Torzite. I made both as light as I could. I used 7'6" blanks rated for 3/8 oz. jigs. I also used carbon fiber grips with exposed blank spinning reel seats. I didn't not do any other decorations to the blank itself. I built my cousin multiple rods and built these rods specific for fishing below a dam.
For that particular fishing a person uses a 1/16th oz jig with a 4 inch plastic. 6 lb braid is a must ! The big walleyes below the dam will not bite if you use 10 lb. braid.
The bait is casted out and left to drift down in the current caused by the hydro electric dam. The 4" white plastic simulates a smelt that is stunned by going through the dam.
My cousin casted and let the plastic drift . He casted for about an hour with the torzite rod. After doing that for the hour he used the rod with the Alconite guides. After three casts he put that rod down and went back to the torzite rod and finished fishing. I later asked him if there was that much of a difference and he said "oh yah". He told me that the Torzite rod casted further, it also seemed lighter and more responsive he told me. He also mentioned that he could get a better feel of the plastic drifting.
To summerise things I guess that if you fish a lot it might be beneficial to spend the extra money and you should notice a difference if you go back to standard inserts. If you are a casual fisherman I am guessing you wouldn't notice much of a difference and the expense might not be worth it.
Guess it compares to a frequent fisherman having a custom rod built to fit his specific needs for maximum performance vs a casual fisherman that would be satisfied getting a rod off a rod rack at a sporting goods store.
Hope this helps...
I would let mu fishing team try them out, I am sure they will switch to torzite guide and tip. its a delicate feeling.
In my opinion these are the Ferrari of guides. Super light and strong. These are my “go to” for high end spinning rods.
Perfection in a single foot spinning guide
Best guides I have wrapped to date
Noticable improvement in casting distance. Very lite and don't need to be ground down. Expensive but worth it in my opinion. I've only built rods for myself and friends so I'm no expert but I have spent a fortune on rods and reels.
